ls series specifications temperature characteristics (max.impedance ratio) category temperature range rated voltage range rated capacitance range capacitance tolerance tangent of loss angle (tan ) esr (1) leakage current ( 2) performance characteristics item 55 to +105 c 2.5 to 16v 100 to 1500f 20% at 120hz, 20 c less than or equal to the specified value at 120hz, 20 c less than or equal to the specified value at 100khz, 20 c less than or equal to the specified value. after 2 minutes' application of rated voltage at 20 c z+105 c / z+20 c 1.25 (100khz) z 55 c / z+20 c 1.25 endurance damp heat (steady state) resistance to soldering heat marking the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 5000 hours at 105 c. the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 1000 hours at 60 c, 90% rh. after soldering the capacitor under the soldering conditions prescribed here as preheat at 150 to 200 c for 60 to 180 seconds and peak temperature at 265 c for 10 seconds or less, the capacitor shall meet the specifications listed at right, provided that its temperature profile is measured at both of terminal ends facing the soldering side. navy blue print on the case top capacitance change tan leakage current ( 2) esr (1) within 20% of the initial capacitance value ( 3 ) 150% or less than the initial specified value 150% or less than the initial specified value less than or equal to the initial specified value capacitance change tan leakage current ( 2) esr (1) within 20% of the initial capacitance value ( 3 ) 150% or less than the initial specified value 150% or less than the initial specified value less than or equal to the initial specified value capacitance change tan leakage current ( 2) esr (1) within 10% of the initial capacitance value ( 3 ) 130% or less than the initial specified value 130% or less than the initial specified value less than or equal to the initial specified value ultra-low esr, high ripple current. load life of 5000 hours at 105 c. radial lead type : lead free flow soldering condition correspondence. compliant to the rohs directive (2002/95/ec). 1 esr should be measured at both of the terminal ends closest to the capacitor body. 2 conditioning : if any doubt arises, measure the leakage current after the voltage treatment of applying dc rated voltage con tinuously to the capacitor for 120 minutes at 105 c. 3 initial value : the value before test of examination of resistance to soldering. p 1 l 2 s 3 1 4 a 5 2 6 7 7 1 8 m 9 d 10 o 11 1 12 configuration size code capacitance toleranc ( 20%) rated capacitance ( 270 f ) rated voltage ( 10v ) series name type l +0.5max. 15min 4min d +0.5 max. resin coated case silvered lead wire d ls 270 a 941 capacitance series lot. no. voltage(a:10v) p 0.5 dimensions type numbering system (example : 10v 270 f) radial lead type, long life assurance dimension table in next page. please refer to page 20 about the end seal configulation. voltage v 2.5 4 6.3 10 16 code e g j a c size d l p d 8 9l 8.0 8.5 3.5 0.6 8 12l 8.0 11.5 3.5 0.6 8 7l 8.0 6.5 3.5 0.6 6.3 9l 6.3 8.5 2.5 0.6 6.3 10.5l 6.3 10.0 2.5 0.5 10 13l 10.0 12.5 5.0 0.6 (mm) ls lf long life conductive polymer aluminum solid electrolytic capacitors cat.8100z
conductive polymer aluminum solid electrolytic capacitors ls series taping specifications are given in page 20, 21, 22. please refer to page 3 for the minimum order quantity. rated ripple current (marms) at 105 c 100khz standard ratings no marked, will be put at 12th digit of type numbering system. 1 2.5 (0e) 16 (1c) 10 (1a) 6.3 (0j) 4 (0g) 2.8 18.4 11.5 7.2 4.6 330 680 820 820 820 1500 270 560 560 680 1200 330 390 470 560 560 820 150 270 470 100 270 330 470 500 340 500 410 410 750 500 448 448 544 960 416 491 592 706 706 1033 300 540 940 320 864 1056 1504 8 15 8 7 7 8 8 15 7 7 8 20 15 7 9 8 8 20 8 8 24 9 9 9 4800 3900 4800 5200 5800 5500 4800 3900 5200 5800 5500 3000 3900 5500 4300 5000 5500 3000 4900 5500 2800 4500 4700 4700 PLS0E331MCO8 pls0e681mc l 2 pls0e821mco8 pls0e821mco6 pls0e821mdo1 pls0e152mdo1 pls0g271mco8 pls0g561mc l 2 pls0g561mco6 pls0g681mdo1 pls0g122mdo1 pls0 j331mdl4 pls0 j391mcl2 pls0 j471mdo1 pls0 j561mco8 pls0 j561mco6 pls0 j821mdo1 pls1 a151mdl4 pls1a271mdo1 pls1a471mdo1 pls1 c101mdl4 pls1c271mdo1 pls1c331mdo1 pls1c471mdo1 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 6.3 9 8 7 6.3 9 8 9 8 12 10 13 6.3 9 8 7 8 9 8 12 10 13 6.3 10.5 8 7 8 12 6.3 9 8 9 10 13 6.3 10.5 8 12 10 13 6.3 10.5 8 12 10 13 10 13 rated capacitance ( f) rated voltage (v) code surge voltage (v) leakage current ( a) esr (m ? ) (at 100khz 20 c) rated ripple (marms) tan part number case size d l (mm) : in this case, will be put at 12th digit of type numbering system. 2 : in this case, will be put at 12th digit of type numbering system. 4 : in this case, will be put at 12th digit of type numbering system. 6 : in this case, will be put at 12th digit of type numbering system. 8 cat.8100z
|
